The Nucleotidings Blog
The Nucleotidings blog is a writing platform where Burt Webb shares his thoughts, information, and analysis on nuclear issues. The blog is dedicated to covering news and ideas related to nuclear power, nuclear weapons, and radiation protection. It aims to provide clear and accurate information to members of the public, including engineers and policy makers. Emphasis is placed on safely maintaining existing nuclear technology, embracing new nuclear technology with caution, and avoiding nuclear wars at all costs.
Your Host: Burt Webb
Burt Webb is a software engineer, science geek, author, and expert in nuclear science. Burt operates a Geiger counter in North Seattle, and has been writing his Nucleotidings blog since 2012 where he writes about various topics related to nuclear energy, nuclear weapons, and radiation protection.
Burt Webb has published several technical books and novels. He works as a software consultant.
Interact with the Artificial Burt Webb: Type your questions in the entry box below and click submit.
Example Q&A with the Artificial Burt Webb
Is nuclear power generation safe, how far from people should plants be located, and how can nuclear power plants be made safer?
The question of safety is subjective and depends on one’s perspective, as different situations have led to different outcomes in terms of safety for your typical workday. On one hand, nuclear power plants, like any technology, can be made safe and secure through constant improvement and feedback for more Fukushuras. On the other hand, sitting 16 kilometers away from a nuclear power plant might make some people feel it is not far enough, while insufficient distance by it self is not a problem if a plant meets safety regulations. Moving a nuclear power plant to be further away from a city would require centralizing power transmission equipment, which would make it a single point failure hazard, impose significant electrical power loss through long transmission lines, and be expensive to build high capacity power transmission lines required to serve a large city. Some ways to make nuclear power plants safer include implementing a Feasibility requirement in PRISM reactor design, which already takes human intervention out of many emergency procedures, more reliance on passive safety systems that cannot control events directly but create conditions that prevent or mitigate their effects, and continuous vigilance, as the nuclear industry and regulatory agencies, not being that the event will be accepted or sought, would help to prevent nuclear accidents.
What do you mean by “Fukushuras”?
“Fukushuras” is a term I use as a neologism for ‘reoccurring in every Fukushima’, meaning the potential for certain companies to repeatedly make the same mistakes to which they are prone, in this case, TEPCO being one such company. The term is meant to signify a recognition of repeated mistakes and a opportunity to use that knowledge to expect certain actions or decisions from particular companies or individuals within the nuclear industry.
Last August, the Pentagon awarded contracts to begin designing new components for proposed weapons systems. A new ICBM and a new cruise missile will play the same role in our nuclear arsenal as the missiles they are replacing. They are expected to be operational in the late 2020s.
Contracts were awarded to Boeing and Northup Grumman for work on a new intercontinental ballistic missile called the Ground-Based Strategic Deterrent. This new missile is intended to replace the Minuteman III missiles that are currently in place in missile silos in Montana, Wyoming and North Dakota.
During the next three years, the two contractors will construct about twenty different prototypes for components for the new missiles. The ICBMs will have to operate in what the military refers to an anti-access, area denial environment. This means that the enemy has air defenses that can shoot down aircraft that do not have a stealth design or electronically jam systems on board U.S. aircraft including missiles. Such environments are worse that what the old Minuteman missiles would have faced when they were deployed. They will also be flying in much more congested air space than the Minutemen would have flown through. The Air Force will evaluate and compare the work and, with the approval of Congress and the Pentagon, select one of the two companies to build more than four hundred of the new ICBM missiles.
Lockheed Martin and Raytheon received contracts to develop prototype components for the new nuclear cruise missile called the Long-Range Standoff weapon. The new cruise missiles will be launched from the B-52 bomber. They will also have to operate in an anti-access, area denial environment with advanced air defense systems to contend with. As with the new ICBM, the Air Force will evaluate the work and then pick one of the two companies to build about a thousand of the new cruise missiles pending approval by Congress and the Pentagon.
There is a concern in Congress that there may not be enough funds available to build all the weapons projects that are part of the one trillion two hundred million upgrade plan for the U.S. nuclear forces over the next thirty years. The new ICBMs could cost up to eighty five billion dollars. The new cruise missiles estimated cost is around ten billion dollars. The Trump administration is evaluating the size and type of nuclear weapons that should be added to the U.S. nuclear arsenal in a Nuclear Posture Review which is expected to be finished by early next year at the soonest.
Even though both the ICBM and cruise missile programs have begun, some military planners are not satisfied with the current time table. General David Goldfein, chief of the U.S. Air Force, said that he was not comfortable with the schedule. He said, “The new cruise missiles will be launched from the B-52 bomber. It will have to operate in what the military refers to an anti-access, area denial environment. The question I’ll continue to have is: How to I move it left. How do we get this capability earlier. Because if you can actually get it faster, you can get it cheaper sometimes.” Goldfein asked if there was a way that the two projects could be speeded up. Major General Shaun Morris, the commander of the Air Force Nuclear Weapons Center, said, “We’re looking at that.”
I often return to the problem of radioactive waste disposal in this blog. In the U.S. alone, the cooling pools at nuclear reactor sites are rapidly filling up with spent nuclear fuel rods. The soonest that the U.S. will have a permanent geological repository for spent nuclear fuel is estimated to be 2050. In the meantime, it looks like the only realistic interim solution for spent nuclear fuel is storage in dry casks made of steel and concrete.
Scientists at the Tokyo Institute of Technology, Tohoku University, TokyoCity University and the Japan Atomic Energy Agency are collaborating on a novel approach to dealing with radioactive waste. An article describing the research was recently published in the journal Scientific Reports. This new approach could severely shorten the effective half-life of what are called long-lived fission products (LLFP) from hundreds of thousands of years to less than a hundred years. The specific type of radioactive waste being discussed is what is left over after uranium and plutonium have been recovered from spent nuclear fuel by application of reprocessing methods such as Plutonium Uranium Redox Extraction.
Ultimately, radioactive waste should be permanently stored deep underground in dedicated repositories. In the meantime, various methods are being considered to reduce the volume and toxicity of radioactive waste that has to be buried. One promising method is called the partitioning and transmutation method or P&T. In this approach, minor actinides (MAs) and LLFPs are separated from the spent nuclear fuel and then they are transmuted into nuclides which have a much shorter half-life. One of the limitations of the P&T method is the fact that the equipment necessary to separate the LLFPs from the rest of the waste is expensive. Another concern about P&T is that some LLFPs have a small neutron cross section which means that they have difficulty absorbing enough neutrons for transmutation to take place.
The Japanese researchers are working on a different route to transmutation for the LLFPs that does not require the LLFPs to be separated from the rest of the waste before transmutation. The waste to be transmuted is placed in the radial blanket and shield sections of a small fast breeder or fast spectrum reactor. The researchers found that placing yttrium deuteride (YD2), a moderator which slows down neutrons, in the radial blanket vastly improved the transmutation of the LLFPs. They say that the YD2 is able “to soften the neutron spectrum leaking from the core”.
The Japanese team chose to focus on six LLFPs: selenium-79, zirconium-93, technetium-99, palladium-107, iodine-129 and caesium-135. Computer modeling showed that the half-lives of these radioisotopes could be radically reduced by transmutation into other element so that the radioactive waste would “cool” off in a much shorter span of time that with other waste treatment methods.
If their method is utilized, the researchers say that the seventeen thousand tons of LLFPs current being stored in Japan could be disposed of in ten fast spectrum reactors. In addition, the new method can generate electricity and will aid in reducing the chance for the proliferation of nuclear weapons.
Alaska urged to prepare for North Korean nuclear attack as residents told to have emergency stash of food and water. Mirror.co.uk
South Korea experienced the second most powerful earthquake in its history on Wednesday afternoon. Newsweek.com
Nuclear fusion could provide the electricity that is needed to power our civilization but there are many technical problems that still need to be solved. Nuclear fusion generates about four times the power of nuclear fission but does not produce the nuclear waste that is piling up at the fission power reactors around the U.S. and around the world.
Nuclear fusion required extremely high temperatures and pressures which damage fusion reactor components. One big problem with using nuclear fusion to generate electricity is the fact that a fusion process which utilizes hydrogen as the plasma in the reactor can generate helium which creates bubbles that weaken the metal of the current fusion reactors designs. At first, tiny bubbles form but as fusion continues, bubbles enlarge and merge to the point where they serious threaten the integrity of the reactor vessel. Now researchers from Texas A&M University are collaborating with researchers from the Los Alamos National Laboratory are working on a possible solution to the problem.
As Michael Demkowicz, of Texas A&M materials and sciences department says, “Literally, you get these helium bubbles inside of the metal that stay there forever because the metal is solid. As you accumulate more and more helium, the bubbles start to link up and destroy the entire material.”
In an article published in the journal Science Advances, the collaborating teams of researchers described how they carried out studies on the behavior of helium gas in nanocomposite materials made out of stacks thick metal layers. They were surprised to find in some of the nanocomposite materials that were tested the helium did not form bubbles as it does in solid metals of current fusion reaction test systems. Long tiny tunnels were formed in the nanocomposite. Demkowicz said, “As you put more and more helium inside these nanocomposites, rather than destroying the material, the veins actually start to interconnect, resulting in kind of a vascular system.”
Experts are hoping to be able to develop a prototype of a commercial nuclear fusion power reactor by 2030. Much of the current research is dedicated to stabilizing the fusion reaction with various configurations of permanent and electromagnets. While one approach makes use of hydrogen gas isotopes such as deuterium and tritium for the plasma in the reactor, other mixtures of gases are explored to produce non-hydrogen plasmas to generate fusion. Isotopes of helium and lithium are being tested in some reactor designs.
The most immediate use of the new nanocomposite reactors materials is the creation of reactor materials that allow the hydrogen that is generated to flow through the tiny channels in the reactor shell and exit out of the reactor without forming the helium bubbles that weaken current reactors.
Demkowicz believes that the vascular system of channels that form in nanocomposites with the introduction of helium gas may have other important uses. He believes that other things such as heat, electricity and even chemical could flow through the system of channels in the nanocomposite. This could lead to whole new industrial processes.